BKZKW - ULTRA-QUARTZ RESIN
- MSDS: BKZKW
- Manufacturer: ITW DEVCON CORP
- Product Name: ULTRA-QUARTZ RESIN
- National Stock Number: 8040-00N017843
Product Identification
Product ID:ULTRA-QUARTZ RESIN
MSDS Date:01/11/1988
FSC:8040
NIIN:00N017843
Kit Part:Y
MSDS Number: BKZKW
Responsible Party
DANVERS, MA 01923
Emergency Phone: 508-777-1100
Info Phone: 508-777-1100
Cage: 16509
Contractor
Telephone: 508-777-1100
Cage: 16509
Ingredients
BISPHENOL A DIGLYCIDYL ETHER RESIN (DGEBA)
CAS: 25060-38-6
Fraction By Weight: >60%
ALIPHATIC GLYCIDYL ETHER
CAS: 68609-97-2
Fraction By Weight: 10-30%
Hazards
LD50 LC50 Mixture:LD50: ORAL(RAT) 11,400 MG/KG (DGEBA)
Routes of Entry: Inhalation:NO Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: MILD IRRITATION. SKIN: MAY CAUSE
MILD IRRITATION. INHALATION: UNLIKELY BECAUSE OF LOW VAPOR
PRESSURE. NO DATA WERE FOUND ON SPECIFIC SYMPTOMS. INGESTION: ACUTE
ORAL TOXICITY IS LOW. NO DATA WERE FOUND ON SPECIFIC SYMPTOMS.
EFFECTS OFCHRONIC OVEREXPOSURE: IN SMALL FRACTION OF POPULATION
(SEE EFTS OF OVEREXPOS)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: (AROUND 1%) TOO MUCH SKIN CONTACT
WITH EPOXY RESINS WILL CAUSE SENSITIZATION. ITCHING, SWELLING, OR
RASHES MAY THEN RESULT FROM FURTHER CONTACT.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, AND OTHER SKIN
DISORDERS.
First Aid
First Aid:EYES: FLUSH EYE WITH CLEAN WATER FOR AT LEAST 15 MINUTES
WHILE GENTLY HOLDING EYELIDS OPEN. GET MED ATTN. SKIN: WASH THORO
WITH SOAP AND WARM WATER. CONSULT A PHYS IF IRRIT DEVELOPS.
INHALATION: REMOV E PATIENT TO FRESH AIR. ADMINISTER OXYGEN IF
BREATHING IS DIFFICULT. GET MEDICAL ATTENTION IF SYMPTOMS PERSIST.
INGESTION: DO NOT INDUCE VOMIT. GIVE TWO GLASSES OF H*2O TO DILUTE.
GET MEDICAL ATTN.
Fire Fighting
Flash Point Method:PMCC
Flash Point:400F,204C
Extinguishing Media:CO*2, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR NIOSH/MSHA APPROVED
SCBA & PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.
Accidental Release
Spill Release Procedures:WEAR APPROPRIATE PROTECTIVE EQUIPMENT. ABSORB
SPILL ON INERT MATERIAL SUCH AS VERMICULITE OR SAND; SCRAPE UP AND
TRANSFER TO IMPERMEABLE CONTAINERS. WASH SPILL AREA WITH STRONG
DETERGENT AND WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE WELL-CLOSED IN COOL, DRY PLACE.
HNDL I/A/W POTENTIAL HAZ OF CURING AGENT. REMOVE CONTAM CLOTHING &
PROT GEAR; CLEAN THORO BEFORE USING AGAIN.
Other Precautions:CONTAM LEATHER ARTICLES (INCLUDING SHOES) CANNOT BE
DECONTAMINATED & SHOULD BE DISCARDED. IF MATL IS SANDED/MACHINED
AFTER CURING,TAKE APPROP PREC AGAINST PARTICULATES (WHICH MAY
INCLUDE SILICA & SILI CATES) WHICH WILL BE GENERATED.
Exposure Controls
Respiratory Protection:NONE REQUIRED AT NORMAL HANDLING TEMPERATURES.
WEAR NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE OF
CONCERN .
Ventilation:LOCAL EXHAUST IS RECOM FOR CONFINED AREAS. GENERAL
MECHANICAL VENTILATION IS ADEQUATE FOR NORMAL USE.
Protective Gloves:CHEMICAL RESISTANT RUBBER GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:PROTECTIVE GEAR AS REQUIRED TO PREVENT SKIN
CONTACT.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING, ESPECIALLY BEFORE
EATING OR SMOKING.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
HCC:N1
Vapor Pres:NIL @ 70 F
Vapor Density:>1
Spec Gravity:1.1
pH:7
Evaporation Rate & Reference:<1
Solubility in Water:NIL
Appearance and Odor:AMBER LIQUID WITH LITTLE ODOR.
Percent Volatiles by Volume:0
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME HEAT & OPEN FLAME.
Hazardous Decomposition Products:OXIDES OF CARBON; ALDEHYDES AND ACIDS
FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS RELEASED WHEN THIS RESIN IS
MIXED WITH EPOXY HARDENERS; USE CAUTION WHEN MIXING LARGE
QUANTITIES.
Disposal
Waste Disposal Methods:AFTER PROPER MIXING W/HARDENER. PROD FORMS A
NONHAZARDOUS SOLID-SEE DIRECTIONS FOR MIXING. UNMIXED WASTE RESIN
SHOULD BE DISCARDED IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL
REGULATION.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.